Full 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the truck arrives.
Before
After
Before
After
Before
AfterClopay Torsion Spring Replacement: The Cedar Park Owner’s Guide
Clopay torsion spring replacement in Cedar Park typically runs $180-$340 installed, and we stock Clopay-compatible springs on the truck so the swap is usually done same day. Most folks discover the spring has failed when the door won’t lift, or when they hear a noise in the garage that sounds like a rifle shot and find the spring snapped clean in two, often with a visible gap in the coil above the door. A Clopay door uses a torsion spring system matched to the door’s weight, cable drum, and shaft, and swapping in the wrong size isn’t a minor mistake; it throws off the balance and wears out the opener motor fast.
Key Takeaways
- Clopay torsion spring replacement in Cedar Park: $180-$340 installed, quoted before work starts.
- Same-day service in most cases; we carry common Clopay spring sizes on the truck.
- Clopay uses specific wire gauges and inside diameters; a generic spring isn’t a match just because it looks close.
- 90-Day Done Right Promise on every spring job, written on the invoice.
Which Clopay Models This Applies To
Clopay builds residential doors under several series names: the Classic, Gallery, Coachman, and Reserve lines, plus the Entry and Value series you’ll see on a lot of Cedar Park spec homes. The torsion spring isn’t chosen by model name; it’s chosen by the door’s weight, the spring’s wire gauge, inside diameter, length, and wind direction. Clopay tends to run a narrower inside diameter on some lighter doors than other brands, and if you bolt on a spring from another maker with the wrong inside diameter, it’ll bind on the shaft, chew itself up, and fail early. The real identifier is the color-coded cone on the spring itself and the measurements stamped or painted on the old spring; we match from those, not from the model sticker alone. We’re an independent shop, not a Clopay franchise, which means we’ll give you the straight answer on whether Clopay OEM or a quality aftermarket equivalent is the better spend on your particular door.
Signs Your Clopay Torsion Spring Replacement Is Failing
- The door feels heavier than it used to. A torsion spring loses tension as it cycles, and before a full snap, the door often gets noticeably harder to lift by hand. That strain transfers straight to your opener gears.
- The opener struggles or reverses. If the motor is grinding, stopping mid-travel, or reversing on the way down, the opener is often blamed when the spring is actually shot; the opener simply can’t compensate for the lost lift.
- A loud bang in the garage. That’s the spring snapping under tension, and it’s the most common way Cedar Park homeowners find out the spring gave out. You’ll usually see the break as a visible gap in the coil.
- The door is crooked going up or down. With one of two springs broken, the remaining spring carries uneven load, and the door cocks to one side in the tracks.
- Cables are loose or off the drum. When a torsion spring breaks, the cable on that side loses tension and can slip off the drum, leaving it hanging or wound around the shaft.
Replacement Cost & What’s Included
Clopay torsion spring replacement in Cedar Park runs $180-$340 installed, and the spread comes down to spring size and whether we replace one or both. Where you land in that range depends on your door’s weight: a light single-car door sits at the low end, a heavy insulated double door with a high-cycle spring at the top. The price includes the spring, the labor to wind and set it, balancing the door, and torquing the hardware back to spec. We’ll also check the cables, drums, hinges, and rollers while we’re up there. The price is quoted before we touch a tool, and it doesn’t change at the door; that’s a promise Otto Reinhardt has kept since he opened the shop here, and it’s written on every invoice along with the 90-Day Done Right Promise. Call (737) 383-3934 for an exact quote; estimates are free, and there’s no trip charge inside the county.
DIY or Call Us?
You can check the obvious: look at the spring above the door and see if there’s a gap in the coil, and test the balance by lifting the door halfway and letting go. What you should not do is touch the winding cones. A torsion spring holds enough torque to break bones or worse if it lets go while you’re winding it, and the cast-iron winding bars most folks buy at the hardware store aren’t sized to the cone, which is how people get hurt. This is a job where the professional isn’t a luxury; it’s the safe call, and it needs to be done with the door clamped, the right bars, and a torque check before the opener ever runs. If you’re in Cedar Park and the spring is broken, call (737) 383-3934; Otto or one of his crew will be out fast, and the name on the van matches the name on the license.
FAQs
A standard Clopay torsion spring is rated around 10,000 cycles, which in a Cedar Park household that opens the door three or four times a day works out to roughly seven to ten years. Texas heat and humidity don’t shorten the spring directly, but they do dry out the bearing plates and make a marginally-balanced door wear everything faster. Ask us about high-cycle springs when we’re out; they’re built for 25,000+ cycles and make sense if you plan to stay in the house.
No. A torsion spring that has snapped can’t be welded, spliced, or re-wound; the metal has failed, and any repair attempt leaves a spring that will fail again, usually sooner and more dangerously. Replacement is the only safe fix, and we replace both springs at once when they’ve aged together, so you don’t pay for labor twice when the second one goes.
A standard Clopay torsion spring replacement takes about an hour to an hour and a half, including balancing the door and checking the cables and drums. If the springs are an unusual size and we don’t have them on the truck, we’ll have them by the next business day; most Cedar Park jobs are done same-day.
Yes. We carry the common Clopay spring sizes and wire gauges on the truck, along with cones, cables, and drums for the usual single and double door setups. We also stock parts for LiftMaster, Chamberlain, and Genie openers, so if the spring failure took out something else along the way, we can usually fix it in the same visit. Call (737) 383-3934 and tell us what the door is doing; Otto will tell you what it needs, usually in about thirty seconds.
Written by Otto Reinhardt, Owner, Otto’s Garage Door - Cedar Park, TX at Otto’s Garage Door, serving Cedar Park and nearby areas.